THIS TRANSMITTER HAS NEW IMPROVED DESIGN UNDER NEW NAME T1013 EAGLE DISTRIBUITED BY ELECTRIFYRC INC. https://hobbywireless.com/t1013-Eagle-13-ghz-500mw1000mw-transmitter
The improvements on new T1013 EAGLE over the "old LawMate" transmitters are:
- Dual user-selectable output power 500mW - 1000mW.
- The new T1013 EAGLE is about 30% lighter than its predecessor T1012 & T1013 LawMate brand.
- A much better higher quality audio channel that can also be used for data-carrier.
- Rust resistant and lighter metal alloy case.
- Old brick aluminum heast-sink has been replaced by light-weight and high efficiency low profile ceramic heat-sinks pads.
The Lawmate's 1013 transmitter has been completely redesigned and tailored for FPV with a handful of improvements, such as: new switching regulator, ceramic high efficency low profile heat sinks, high quality audio channel, runs 50% cooler than its previous model, lower profile, 10 grams lighter and overall better performance.
It's a power house, providing a 1000 milliwatts (1W) of pre RF output. It is the best transmitter for long range applications. (for RC models is recommended to install this as far as possible away from the models receiver) Even with all that power, it weights only around 1.2oz (32grams). With all this, and the right setup, for sure you can get video reception miles away. It is highly recommended to install the transmitter in ventilated areas, to allow the air to keep it cool.
This transmitter has digital Phase-Lock-Loop circuit avoiding frequency drift, providing a stable and solid audio and video delivery. You can not go wrong with it.
RF output power: 1000mW (1W)
(4) User-selectable channels: (1200MHz, 1240MHz, 1258MHz and 1280MHz)
Operating Band: 1.2/1.3 GHz
Works with any camera PAL or NTSC
Digital Phase-Lock-Loop circuit no drifting problem
Works with any of our receivers
Audio and Video cable with RCA adapter
Highly integrated circuit
High reliability/linearity/AIGaAs/GaAs FET amplifier module
Uses digital phase-lock-loop circuit without temperature drifting problem
Weight: 30g (transmitter only)
Output power 50-ohm load CH1 Vcc = 12V: 30dBm (1000mW)
Nominal output impedance: 50 ohms
Operating voltage: Vcc, 10.5V (minimum), 12V (typical), 13V (maximum)
Supply current Vcc = 12V: 350mA (typical), 400mA (maximum)
Video input voltage 75-ohm impedance: 1Vp-p
Audio input voltage 10k ohm impedance: 1Vp-p
Sub carrier frequency: 5.5MHz
Operation temperature: -10 to 40 degrees Celsius
Storage temperature: -40 to 80 degrees Celsius
Operating humidity: 20 to 80%
Storage humidity: 10 to 80%
Dimensions and weight: 50 x 26 x 11mm, 0.93oz (26g) (without antenna)
Standard shipping package:
1.2/1.3 GHz 1000mW AV transmitter
SMA type dipole antenna x 1
Jack connector to RCA AV input and power input cable x 1
Click here to see the transmitter and camera connections.
Click here to see compatible receivers
It's absolutely illegal to ship the Non-US version of this transmitter to any US address, please do not insist. Retailer and recipient are subjected to VERY EXPENSIVE fine.
No license is required to purchase it, however in order to legally use and operated of this device in the United State of America a HAM license is required. To operate/use in other countries other than US please check the local rules before using it, some countries may forbid its use entirely.
By purchasing this equipment, you are agreeing that you understand the rules and assume total responsibility to legally operate the equipment. For information on how to obtain an amateur radio license, visit http://www.arrl.org/getting-licensed.
It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices.
Hobby Wireless is not responsible any damages, losses, illegal operation or changes made by the user to the transmitter will be totally the user's responsibility.